AERaudit muestra el potencial de ahorro en las plantas de tratamiento de aguas residuales Produce con eficiencia energética mejorada y se mantiene competitivo para AERZEN Load operation in wastewater treatment plants is subject to considerable fluctuations. Collection and subsequent evaluation of the operating data from a blower station with the high-precision methods of AERaudit delivers actionable results on the current utilisation and efficiency, and informs how it can be designed to run much more efficiently in the future. AERaudit muestra de forma transparente los potenciales de ahorro de las depuradoras Con AERaudit, AERZEN determina la demanda de carga exacta de las depuradoras. AERaudit es un servicio innovador desarrollado exclusivamente por AERZEN para mejorar la eficiencia energética de las depuradoras. Los municipios en particular dependen de los ahorros, ya que las depuradoras son los mayores consumidores de energía. Entre un 60 y un 80 % de la demanda global de energía de una depuradora se produce en el ámbito de la aireación biológica. Como especialista en análisis, AERZEN es socio competente para comprobar y analizar la energía de forma pertinente con el fin de optimizar energéticamente las estaciones soplantes. La base para que una depuradora funcione con eficiencia en materia de energía y procesos es analizar la situación y evaluar los datos de servicio actuales. En este sentido, la demanda de carga real debe registrarse y a continuación se muestran los potenciales de ahorro. En tres pasos, AERaudit permite determinar la configuración más rentable y orientada al futuro de las instalaciones. El servicio AERaudit es un componente de Agua 4.0, una innovadora orientación hacia procesos en la gestión del agua. Como uno de los líderes del mercado en técnica de aguas residuales, AERZEN acompaña a sus clientes en el camino hacia el agua 4.0 con el concepto global AERwater, que engloba soluciones de digitalización, automatización y eficiencia de recursos. A este respecto, AERaudit facilita la base de datos. Three steps to transparency1. On-site measurement: the AERZEN service team brings transparency to the key figures of your blower station. A mobile measuring station records the relevant data in your ventilation system. Volume flow, system pressure, temperature and kW output are measured live and recorded in the form of load profiles. 2. Analysis: evaluation of the recorded data is carried out carefully and in detail at AERZEN headquarters – every low and peak load, no matter how small, is registered. Based on the results, AERZEN experts then develop one or more solutions tailored to customer requirements that are as efficient as possible. 3. Report: all data of your blower station is displayed in detail and transparently. Temperatures, load profiles and energy consumption are visualised and explained in detail in the form of diagrams. We will also show you your customised Performance3 solution with the ideal machine configuration. In addition, what the saving potential of energy or CO2 is and which amortisation times can be achieved. Contact person: Markus Leidinger, Application SpecialistWastewater Technologymobile: +49 175 9335602e-mail: markus.leidinger@aerzen.de
Securing subsidies for energy efficiency Thanks to public subsidy programmes, energy efficiency now has a double pay off. In order to exploit this potential, AERZEN will offer its customers comprehensive support in the areas of energy efficiency, energy recovery and resource management together with the state-subsidised e.qua network. The climate protection targets adopted by the German government are accompanied by numerous subsidy programmes that can be used by operators of water management facilities. A distinction must be made between concept and investment subsidies for energy in the context of climate protection.Customer-oriented support by AERZEN and e.qua ranges from measuring volume flow requirements, energy analysis and optimisation and the preliminary clarification of suitable funding options for energy concepts to support in applying for funding.One example is sewage treatment: wastewater treatment plants are among the largest energy consumers in municipalities. With the latest technologies, considerable amounts of energy can be saved. In order to meet the increased requirements of the water and wastewater industry, AERZEN has paid special attention to the energy efficiency of its assemblies. In addition, well thought-out solutions for waste heat utilisation can be provided. AERZEN thus also meets the political targets set for energy efficiency and energy generation.
Delta Blower series extended With the Generation 5 positive displacement blowers AERZEN has set new standards. Now, the series is extended by two new blower stages: GM 110 S and GM 130 S types close the gaps in the volume flow range. The figures “110” and “130” stand for intake volume flows of 110 and 130 m³/min respectively (6,660 and 7,800 m³/h). Previously, there had been a jump from 90 m³/min (5,400 m³/h) to up to 150 m³/min (9,000 m³/h) and with it also a jump in the nominal diameter from DN250 to DN300. With the new blower sizes, this volume flow range is now finer graded, which brings decisive advantages for plant manufacturers and operators in terms of investment costs, dimensions and control range.What is also new: the enhanced Delta Blower series G5plus. Energy efficiency is currently the most important focus, particularly in the field of compressor technology where energy costs exceed 90% of the life-cycle-costs. AERZEN has always been a standard setter to develop more efficient and environmentally friendly processes. To expand upon the success of the AERZEN Delta Blower series, an exciting new design sets energy saving records. The new G5plus series distinguishes itself by increased energy efficiency of up to 5% and significantly reduced dimensions.Experience the new blower sizes at the trade fair stand of Aerzener Maschinenfabrik at the IFAT in Munich and the ACHEMA in Frankfurt.
This is AERZEN Performance³ AERZEN defines Performance. as an individual solution for the oxygen supply of biological aeration in waste water technology. Individual assemblies of Delta Blower positive displacement blowers, Delta Hybrid rotary lobe compressors and Aerzen Turbo blowers of the AERZEN range of products or a combination of assemblies of different efficiencies and regulating ranges can be used. What is so special about Performance³ Every technology has its strengths, but is also subject to physical limitations. By means of a possible technology mix and the use of different sizes, the individual strengths of assemblies can be added to a highly efficient combination with the best control range. The AERZEN Performance³ concept takes into account the respective requirements of a plant and offers you a rightsized solution that suits you and your plant perfectly. You will be supported by AERZEN wastewater experts during the entire process until your Performance³ solution is found. How does AERZEN proceed? In a first step, the load profile of a wastewater treatment plant is evaluated and important parameters for the following calculations are determined. If this load profile is not known it makes sense to record the measured value before. For this purpose, AERZEN uses its AERaudit product which is used to measure the volume flow and other important variables during operation of a plant (see page 2).An analysis of the recorded load profile forms the basis for the Performance³ process. At the beginning, the solution space consists of a multitude of variants. Taking your plant requirements into account, AERZEN will develop the Performance³ solution that best suits you and your plant.
New Head of Opportunity Engineering in Supply Process Gas On 1 September 2017, Carsten Holldack assumed responsibility for the group Opportunity Engineering in the Supply Process Gas division. The graduate mechanical engineer, born in 1970, has more than 20 years of professional experience in the field of rotating equipment. His previous roles were in development, product management and salesmanagement. The “Opportunity Engineering” group at the Aerzen site, led by Holldack, consists of six experienced process gas specialists.
Klaus Peter Glöckner new member of the General Management Since 1 December 2017, the General Management of Aerzener Maschinenfabrik consists again of three persons: Graduate engineer Mr. Klaus Peter Glöckner completes the Management team and has got to know the company intensively over the past few months. Klaus Peter Glöckner is responsible for the EMEA region. He was previously employed as Chief Sales Officer and Managing Director at Messrs. Kelvion.
Aerzen Colombia celebrated its 10th anniversary On 27 September 2017, Aerzen Colombia S.A.S., based near the capital, Bogotá, celebrated its tenth anniversary. The subsidiary, which when it opened was called Aerzen Andina, started out as an agency of Aerzen Iberica. This developed into two separate subsidiaries - Aerzen Colombia, which now has 15 employees, and Aerzen Andina Peru, where four colleagues are currently employed. The markets in Bolivia, Ecuador and Venezuela are supervised by commercial agents. Ricardo Castillo, Managing Director of Aerzen Colombia, is pleased about the tenth birthday celebrations: “We hope to be able to celebrate many more anniversaries and to contribute to the growth of the AERZEN group.”