Protección acústica a medida: AERZEN confía en las ventajas de los silenciadores reactivos 21/04/2017 Con silenciadores reactivos, AERZEN reduce las emisiones de ruido en el lado de descarga de sus compresores de tornillo, soplantes de desplazamiento positivo y compresores de émbolos rotativos. El concepto innovador de estos silenciadores reactivos es superior a los silenciadores disipativos clásicos en muchos aspectos. Las ondas sonoras que se desarrollan en el lado de descarga de un compresor Delta Screw fabricado por AERZEN pueden alcanzar de 170 a 190 dB. Por lo tanto, es obligatorio un silenciador aguas abajo, al igual que con todos los compresores habituales. Las altas frecuencias de las ondas sonoras provocan considerables fuerzas de vibración que tienen un efecto perjudicial sobre las tuberías y el material aislante en los silenciadores disipativos convencionales. Esta llamada micro fricción desgasta el material del filtro con el tiempo y puede dañar incluso el acero inoxidable a largo plazo. Esto conduce a una reducción de la eficacia del silenciador y a la erosión de las partículas más finas. Estos contaminan el aire de proceso y pueden generar riesgos para la higiene, por ejemplo, en la producción de alimentos o pueden obstruir los elementos de aireación de poros finos en el depósito de aireación de una planta de tratamiento de aguas residuales. Deben utilizarse filtros aguas abajo, lo que conduce a pérdidas de presión, niveles de eficiencia reducidos, eficiencia energética reducida y mayores gastos de mantenimiento. La otra forma: neutralizar en lugar de absorber Con los silenciadores reactivos patentados (EP1857682) AERZEN no solo neutralizó el ruido, sino también los problemas antes mencionados. Un sistema de tuberías especial genera un contrarruido definido, que superpone las ondas sonoras con un cierto retraso y las neutraliza. La conducción del sonido debe diseñarse exactamente para la fuente de sonido correspondiente mediante diferentes longitudes y diámetros de tubería. AERZEN ha dominado esta hazaña a la perfección, especialmente en los sistemas de transporte de gases de proceso (División de gases de proceso) los conjuntos están diseñados especialmente para la aplicación correspondiente y el silenciador es siempre un elemento individual. El concepto es tan convincente que AERZEN ahora también equipa los compresores de tornillo de accionamiento directo con silenciadores reactivos. Los módulos perfectamente afinados no se desgastan, no requieren mantenimiento y cumplen con los estándares internacionales PED y ASME. El concepto proactivo ATEX ya proporciona una solución certificada por TÜV. Un parachispas integrado evita que se produzcan chispas en la zona peligrosa en caso de emergencia. La instalación de parachispas en el lugar puede omitirse por completo, una ventaja decisiva para el cliente. Estos importantes componentes son fabricados por la filial Emmerthaler Apparatebau. Por lo tanto, AERZEN logra un alto nivel de flexibilidad y calidad, en particular para los requisitos especiales de los clientes.AERZEN reactive silencersAERZEN reactive silencers - durable, quiet, and ATEX certifiedThe Aerzener Maschinenfabrik uses specially developed reactive silencers in screw compressors and positive displacement blowers. Compared to conventional silencers, these offer several advantages.Positive displacement blowers, screw compressors, and rotary compressors from AERZEN are used in a variety of industries for compressing and conveying air or gases. Depending on the industry, the processed air generated in the assemblies is used quite differently: in the wastewater industry for the enrichment of oxygen in settling tanks, in the food industry for the conveyance of groceries (e.g. flour), or in the cement production for the transport of fuels (such as carbon dust or fluff).The rotary pistons resp. rotors in the machines are driven by a motor and can reach very high speeds. The medium (process air or gas) is conveyed through the rotary pistons, or is compressed by the rotors and guided into the piping system. This results in high noise emissions of up to 170 or up to 190 dB. The attenuation is based on a downstream silencer which is installed on the discharge side of the machines. The sound waves generate high pulsations as well as high temperatures which, in addition to the noise emission, can also lead to material fatigue on the insulating material of conventional absorption silencers.To counteract this problem, AERZEN uses so-called “reactive silencers” on the discharge side of its standard products. These, in contrast to conventional silencers, manage without insulating material. The noise is neutralised in the silencers developed by AERZEN. This technology is a new development, for which the mechanical engineers from AERZEN even have a patent.Absorption silencers - contamination of the process or conveying air by abrasionConventional silencers are lined with insulating material. Due to the high material stress from the sound development, as well as the prevalently high temperatures in the long term, the insulating material is dissolved. This can contaminate the airflow in the machines, since the high frequencies cause micro-friction, resulting in the erosion of very fine particles from the absorption layer.This removal of absorption material is also problematic for several reasons: If machines are used in the food, pharmaceutical or chemical industries, there is a risk of contamination if the product encounters the process air. When used in wastewater treatment plants, the fine-pored aeration elements can be clogged in the aeration tanks.The discharge of fine particles also leads to a higher noise emission over time and to a higher maintenance expenditure in the long term.In addition, a pulsation chamber for smoothing the sound waves is installed in the absorption silencer between the blower and the silencer, resulting in additional energy loss.Reactive silencers - AERZEN sets new standards with innovative technologyWith the patented reactive silencers (EP1857682), AERZEN has succeeded in finding a solution to these problems. For the so-called “absorption-free” or “reactive silencer”, the use of absorption material can be omitted. Contamination of the process air by abrasion of the insulating material is avoided. The occurring sound waves are erased by the destructive interference method instead of damping materials. The sound waves are neutralised by counter-waves. This anti-noise method is also successfully used in other areas as noise protection - for example: high-tech headphones from aircraft pilots are equipped with this system.The AERZEN technology for sound waves leveling in reactive silencers works as follows:the sound waves are measured first. Based on the measured frequency, a precise balanced sound is produced in an inner piping system, which superimposes the original sound waves in a time-offset manner, thus eliminating them. The AERZEN development team makes it possible to adapt these controls very delicately and individually to every application – thus, the right solution is achieved for every customer-specific application.With the AERZEN silencers, the resulting pressure losses are additionally reduced by corresponding inflow ducts. The downstream piping system is less stressed, resulting in a longer service life.Process safety, work safety, energy efficiency, and explosion protectionFor the silencers and machines, this primarily means high process reliability in the respective application. By avoiding abrasion, the process air remains pure, downstream processes are not affected by polluted process air. As opposed to absorption silencers, the duct pressure is not increased. The reactive silencers can be completely omitted with the pulsation chamber installed in absorption silencers, for smoother sound waves, which also means additional energy losses. The AERZEN silencers also increase energy efficiency.While conventional silencers are becoming increasingly louder and more time consuming due to the increasing effectiveness of the insulating material, the acoustic level in the reactive silencers does not change. The efficiency remains constant. This sustained noise reduction not only extends the life of the machines and reduces maintenance, but also guarantees long-term safety by constant noise protection. The noise emissions remain constant and the noise protection measures do not need to be adjusted.Many applications of the positive displacement blowers and compressors require special explosion protection. Thus, (e.g. in the food industry when conveying flour with process air) the material being conveyed is precisely atomised and can ignite on contact with sparks flying. Often, Ex-protection is also required in the chemical industry (e.g. usages in which the direct transport medium is not air, but a gas mixture which requires an ATEX environment, due to its chemical properties). Here, AERZEN proposes the design of its reactive silencers with one flap, thus bringing a third decisive advantage: the innovative construction inside the silencers not only ensures that the sound waves are extinguished here - the discharge silencer also acts as spark arrester and is certified by the TÜV Nord according to ATEX directive 2014/34/EU.For certain - ready for international useAERZEN screw compressors, rotary piston compressors, and positive displacement blowers are distributed and used worldwide. Since strict safety requirements apply to European machine manufacturing and marketing, the assemblies must meet international safety standards. The silencer modules of Aerzener Maschinenfabrik therefore comply with the international Pressure Equipment Directive (PED) 2014/68/EU and the Pressure Equipment Directive (PED). In addition, they are compliant with the regulations of the association for pressure vessels of the American Society of Mechanical Engineers (ASME).
30/04/2018 - Performance³ - La próxima generación. La actividad biológica representa hasta el 80% del total de las demandas energéticas en una planta de tratamiento de aguas residuales. Aerzener Maschinenfabrik se ha propuesto la tarea de encontrar potenciales energéticos ocultos en la aireación para mejorar su eficiencia y optimizarla: Performance³... leer más
23/04/2018 - Expansión del producto para la soplante de desplazamiento positivo La extensa serie de ensamblajes de Aerzener Maschinenfabrik se ha ampliado para cubrir caudales de entrada de 6600 m3/h y 7800 m3/h. Esto permite a AERZEN, uno de los líderes mundiales del mercado en tecnología de soplantes, ofrecer a sus clientes tamaños de soplantes aún más precisos. Los... leer más
09/04/2018 - Interconexión perfecta en toda Alemania Una perfecta disponibilidad de las máquinas también tiene que ver con estar cerca. Por eso, AERZEN amplía su red de servicio técnico de forma continua. Los nuevos puntos de atención en Mönchengladbach, Essen y Trier comenzaron su trabajo recientemente para estar en el lugar rápidamente y... leer más